Public Works Banner

Section 2 - Water

Report-a-Problem-Engineering-Button 

 

The City of Glendora SD & S for Public Works construction can be viewed, downloaded and printed from this site. 

Index - Water pg1
Index - Water pg2
SD&S 2.00 - Standard Construction Notes for Water Improvements
SD&S 2.01 pg1 - Flushing/Disinfecting Procedures for New Water Main Installation
SD&S 2.01 pg2
SD&S 2.03 - Hydrostatic Testing Procedures for New Water Main Installations
SD&S 2.04 - Approved Materials for Fire Service Connections, 4"-10"
SD&S 2.05 pg1 - Approved Materials for 1", 1 1/2", 2" Services
SD&S 2.05 pg2
SD&S 2.07 - Notice of Change Approval
SD&S 2.08 - Thrust Block Requirements for Ductile Iron Mainline
SD&S 2.09 pg1 - Fire Hydrant Assembly - Type I
SD&S 2.09 pg2
SD&S 2.10 pg1 - Fire Hydrant Assembly - Type II
SD&S 2.10 pg2
SD&S 2.11 pg1 - Air/Vacuum Release Valve Assembly, 1" for Ductile Iron Mainline
SD&S 2.11 pg2
SD&S 2.12 - Protective Cover - Type I
SD&S 2.13 - Water Meter Installation Policy Installation and Scheduling Requirements
SD&S 2.14 pg1 - Meter Conduit Requrements for AMR Installations
SD&S 2.14 pg2
SD&S 2.16 - Valve Box Assembly - Type I, Type II for Use in Concrete Surfaced Areas (Low speed vehicular traffic only)
SD&S 2.17 - Valve Box Assembly - Type III for Use in Asphalt Surfaced Areas
SD&S 2.18 - Standard 2.17 - Advisory Note Case II Advisory Note for Use on Improvement Plans
SD&S 2.19 - Pressure Connection, 4" - 10" from Steel to Ductile Iron Mainline
SD&S 2.20 - Blow Off Assembly, 1-1/2", 2" for Steel/Ductile Iron Mainline
SD&S 2.21 pg1 - Flushing/Sampling Connection for New Main Construction
SD&S 2.21 pg2
SD&S 2.22 pg1 - Double Check Valve Assembly - Type I for Fire Service Connections, 4" - 10"
SD&S 2.22 pg2
SD&S 2.23 - Test Plate Installation - Type I for New Main Construction
SD&S 2.24 - Protective Post - Type I
SD&S 2.25 - Service Assembly, 1" Copper for Steel/Ductile Iron Mainline
SD&S 2.27 - Service Connection, 1", 1 1/2", 2" for Steel Mainline
SD&S 2.28 - Meter Installation, 3/4", 1" for New Construction
SD&S 2.29 - Service Assembly, 1-1/2", 2" Copper for Steel/Ductile Iron Watermain
SD&S 2.30 - Minimum Installation Requirements for Backflow Prevention Devices
SD&S 2.31 - Service Lateral Grade Adjustment for 1-1/2", 2" Copper Service Assembly
SD&S 2.32 - Test Plate Installation - Type II for New Main Construction < 100 Feet
SD&S 2.33 - Flushing/Testing Protection for New Main Construction
SD&S 2.34 pg1 - Flushing/Sampling Connection for New Main construction < 100 Feet
SD&S 2.34 pg2
SD&S 2.35 - Water Quality Testing Sequences for New Main Construction
SD&S 2.36 pg1 - Water Quality Testing Sequences Supplemental Chart
SD&S 2.36 pg2
SD&S 2.37 - Approved Service Connection for Residential Service
SD&S 2.38 pg1 - Approved Service Connection for Commercial Service
SD&S 2.38 pg2
SD&S 2.39 pg1 - 1" Serivice Installation/Tie In for Single Service Replacement
SD&S 2.39 pg2
SD&S 2.40 pg1 - 1" Service Installation/Tie In for Dual Service Replacement
SD&S 2.40 pg2
SD&S 2.41 - Service Protection for Site Demolition
SD&S 2.42 pg1 - Service Manifold Assembly for Multiple 1" Service Assemblies
SD&S 2.42 pg2
SD&S 2.43 - Tie In/Test Installation for Ductile Iron Main Construction
SD&S 2.44 - Blow Off/Flushing Assembly for Use with 2" Service Assembly
SD&S 2.45 - Protective Cover - Type II for 2" - 6" Air Vacuum Release Assembly
SD&S 2.46 pg1 - Air Vacuum Release Assembly, 2" for Ductile Iron/Steel Mainline
SD&S 2.46 pg2
SD&S 2.47 pg1 - Sample Station Assembly, 1" for Bacteriological Sampling
SD&S 2.47 pg2
 

As an alternative, a full set of SD & S can be purchased at the Public Works Department public counter for $25.  This set can be kept as a master copy and updated by downloading and printing only those drawings that have been revised. The SD & S may be updated from time to time as required, without prior notice. It is the responsibility of interested parties to keep their master copies of these documents current. It is the contractors' responsibility to obtain and maintain up-to-date copies of the standard drawings while performing any work in the Public Right-of Way.

For additional information please contact:

City of Glendora – Public Works Department
(626) 914-8246
Monday – Thursday 8:00 AM – 5:00 PM

Free viewers are required for some of the attached documents.
They can be downloaded by clicking on the icons below.